|
Post by tony on Dec 22, 2007 19:21:20 GMT
probably has but makes it higher up the rev range and it simply couldnt rev that high with that gearbox combination.
|
|
|
Post by breezer on Dec 22, 2007 19:28:53 GMT
THAT'S IT!!!!!
They're all for sale - I'll NEVER understand the bastard things.
Golf. That's where the clever money is. Plus fours, nice tweed cap, g'n't in the 19th hole...
|
|
|
Post by tony on Dec 22, 2007 19:30:24 GMT
;D
|
|
|
Post by adspeed on Dec 22, 2007 20:28:33 GMT
You talkin' bout women again??
|
|
|
Post by breezer on Dec 22, 2007 20:34:35 GMT
Don't joke about it - I'm living in a house full of wimmin!
I seek solace up here on't pc or in the garage...
|
|
|
Post by breezer on Dec 23, 2007 10:10:33 GMT
Do you think a better pipe than the Leo Vince "performance" lhs pipe would give my primmy the grunt to pull the 2.56?
If so does anyone know which (suitable) pipes will fit with the lhs panel toolbox?
|
|
|
Post by tony on Dec 23, 2007 18:05:02 GMT
my fella, the jl down and forward fits with et3 toolbox. Its not that revvy, i've got standard gearing,standard 4th with a tuned (lo timings tho) malossi. It works fine pulling 4th no problem..its not a hi rev pipe. Its not the best for out and out power but i'm not chopping my bike up.
|
|
|
Post by adspeed on Dec 23, 2007 18:36:11 GMT
bREEZER i HAVE A sIMONINI d AND f DOING NOWT IF YOU WANNA GIVE IT A GO JUST BOB ROUND
fUCKIN cAPS lOCK!!! ;D
|
|
|
Post by breezer on Dec 23, 2007 19:00:25 GMT
Nice one. We'll ave a look at that when the weather improves Adam.
Can someone explain to me (in 7 year old terms) the timings thing? Low timings etc?
|
|
|
Post by tony on Dec 23, 2007 19:28:44 GMT
hey ad, you been celebrating christMaS AlREAdy?
|
|
|
Post by jonnysnatchsniffer on Dec 24, 2007 9:58:42 GMT
my last polini 130 ran primmy gearing cut crank (20mm) with a 24 dellorto, leovince pipe and a 3.50/10 rear tire and 2up to margate i still had to slow down for the p2s i was riding with,and that was with only half a piston, but on the other hand ive had a heavilly ported polini 130, handmade expansion and 34 dellorto and it would only pull v90 primarys and a 300/10 but it used to rev its tits off and eat pistons and bearings, it was fun but expensive, ive nearly always ran primmy gears with polinis with no problem
|
|
|
Post by MiNiKiN on Jan 2, 2008 22:12:56 GMT
Breezer, the standard polini will usually pull a 2.56*. It very much depends on which exhaust you are going to use. You probably shall opt for an Et3 standard exhaust ("the banana"), this gives a smooth, torquey power delivery. Polini left would do as well. *Considering approx. 10 stone weight
|
|
|
Post by breezer on Jan 3, 2008 6:27:40 GMT
* Considering approx. 10 stone weightGentlemen we MAY have found the problem
|
|